Russound A-C68 Instructions d'exploitation

Naviguer en ligne ou télécharger Instructions d'exploitation pour Jeux de haut-parleurs Russound A-C68. Russound A-C68 Operating instructions Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
A-K4
Amplified Keypad with Multisource Capability
for A-BUS
®
System
Installation Manual
A-K4 Overview
The Russound A-K4 is an in-wall amplified keypad used
with A-BUS hubs and controllers in a distributed audio
system. It can be used with both single and multisource
A-BUS hubs/controllers. The A-K4 provides source selec-
tion and control with backlit push buttons, plus an IR
window to receive remote control signals.
The volume up/down buttons control the speakers in
the room that are connected to the A-K4. Typical installa-
tions place one A-K4 in each room of the A-BUS system.
The Line Out connection on the A-K4 can be used to
feed a separate powered subwoofer or to connect an
external amplifier for more power to a larger listening area.
A-K4 Key Features
Power On/Off button (acts as source select with
multi-source hubs/controllers)
Volume trims for L/R balance and maximum level
settings
Built-in IR receiver with IR confirmation LED
IR control of settings and sources via A-LRC2 optional
remote
Line Out connection for external amp or powered
subwoofer
White backlit buttons
A-K4 Speci cations
Output Impedance: 8 ohms/channel (1 pair speakers)
Input Impedance: 10 kohms
Power Requirements: +24VDC 660mA peak
CAT-5 Connections: RJ-45
Dimensions (in-wall): 1.75”W x 2.875”H x 1.75”D
(45x73x45mm)
Weight: 5.5oz. (160g)
Safety Instructions
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance in the oper-
ating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions
should be followed.
5. Water and Moisture - The appliance should not be used
near water; for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool.
6. Wall or Ceiling Mounting - The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
7. Heat - The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
8. Power Sources - The appliance should be connected to
a power supply only of the type described in the operating
instructions or as marked on the appliance.
9. Grounding or Polarization - Precaution should be taken so
that the grounding or polarization means of an appliance is
not defeated.
10. Object and Liquid Entry - Care should be taken so that
objects do not fall and liquids are not spilled into the enclo-
sure through the openings.
11. Damage Requiring Service - The appliance should be ser-
viced by qualified service personnel when:
The power supply cord or the plug has been damaged;
Objects have fallen, liquid has been spilled into the
appliance
The appliance has been exposed to rain
The appliance does not appear to operate normally
The appliance has been dropped or the enclosure is
damaged.
12. Servicing - The user should not attempt to service the
appliance beyond that described in the operating instruc-
tions. All other servicing should be referred to qualified ser-
vice personnel.
13. Care – From time to time you should wipe off the front
panel with a soft dry cloth.
Russound, Inc. 5 Forbes Rd., Newmarket, NH 03857, USA
tel 603.659.5170 • fax 603.659.5388 www.russound.com
technical support: 866.888.7466 e-mail: [email protected]
28-1376 04/08/13 Rev.1
Copyright ©2012 Russound® All rights reserved. All trademarks
are the property of their respective owners. Russound is not
responsible for typographical errors or omissions. Speci cations
are subject to change without notice.
A-BUS is a registered trademark of LeisureTech Electronics Pty
Ltd Australia. This product may be covered by one or more of the
following patents: US #7,181,023, #6,389,139; EP #1004222, AU
#739808, NZ #502982, Mexico #241196, Canada #CA2301062.
Warranty and Repair
The Russound A-K4 is fully guaranteed against all defects in material-
sand workmanship for two (2) years from the date of purchase. During
this period, Russound will replace any defective parts and correct any
defect in workmanship without charge for either parts or labor. For
this warranty to apply, the unit must be installed and used according
to its written instructions. If service is necessary, it must be performed
by Russound. The unit must be returned to Russound at the owner’s
expense and with prior written permission. Accidental damage and
shipping damage are not considered defects, nor is damage resulting
from abuse or from servicing by an agency or person not specifi-
cally authorized in writing by Russound. This Warranty does not cover:
Damage caused by abuse, accident, mis-use, negligence, or improper
installation or operation; Power surges and lightning strikes; Normal
wear and maintenance; Products that have been altered or modified;
Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed. Russound sells products only
through authorized Dealers and Distributors to ensure that customers
obtain proper support and service. Any Russound product purchased
from an unauthorized dealer or other source, including retailers, mail
order sellers and online sellers will not be honored or serviced under
existing Russound warranty policy. Any sale of products by an unau-
thorized source or other manner not authorized by Russound shall
void the warranty on the applicable product.
Damage to or destruction of components due to application of exces-
sive power voids the warranty on those parts. In these cases, repairs
will be made on the basis or the retail value of the parts and labor. To
return for repairs, the unit must be shipped to Russound at the owner’s
expense, along with a note explaining the nature of service required.
Be sure to pack the unit in a corrugated container with at least three (3)
inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at 866.888.7466 for
a Return Authorization number. Write this number on the shipping
label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket,
NH03857.
A-K4 Keypad Front Panel Operation
Volume Level - Volume level indicator LEDs light up from
bottom to top to indicate volume level. Also indicates
source selected (1-6) when in “multi-source” mode.
Status LED - Green LED lights to show Status “on” and turns
off when Status is “off”
Power - Turns zone ON when pressed once. (In multisource
mode, when ON, press and hold will turn zone OFF. When
OFF, press and hold will turn OFF all zones.) Status LED
remains lit when keypad/zone is OFF if any other zone in
system is ON.
Source select (Multisource controller) - When the keypad
is set in “Multisource” mode, the power button is used to
toggle through and select a source. Tap the power button
to toggle between 1 and 6 multiple sources (once power is
on). The top LEDs of the volume indicator show (from top
to bottom) the source that is selected (top LED is source 1,
next LED down is
source 2, etc).
Volume Up/Down - Raises/lowers room volume
IR Receiver - Receives IR signals from a remote control.
Source components attached to IR emitters in an A-BUS
system can be controlled with their own remote controls or
A-LRC2 learning remote aimed at the A-K4.
IR Confirmation LED - Red LED blinks to confirm IR signal
reception.
A-K4 Keypad
2
2
3
4
5
3
3
4
5
6
6
1
1
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Installation Manual

A-K4Amplified Keypad with Multisource Capabilityfor A-BUS® SystemInstallation ManualA-K4 OverviewThe Russound A-K4 is an in-wall amplified keypad used

Page 2

Note: Amplified keypads are shipped with the Status LED option disabled (default).Status function and operation:When the source is powered on, the Sta

Commentaires sur ces manuels

Pas de commentaire